Large Radius Tool

An area for all Q&A's about machining.
User avatar
jimmib
Lurker
Posts: 91
Joined: Tue Oct 25, 2011 1:35 pm
SELF INTRODUCTION: Hello everyone. first of all a big thanks to "Dan the Man". Some of you know me from the previous (2) boards and some don't, so here goes. I have been a fabricator/welder for over 40 years now. Damn that's a helluva long time to do anything! Anyways, I have built literaly 100's of street rods, pro streeters, racecars, bikes and trikes over the years. Never made the headlines and never will. I do what I do because it is the love of my life.
I enjoy reading the posts on the forum and try to contribute when I can. I am sure that this will be every bit as good as the CBH forum, as we will have most of the same folks. Good luck and post a lot of pics!! Jim
Location: Lowcountry USA

Re: Large Radius Tool

Post by jimmib »

Nice Tool. What about chatter? Do you have any problems in that area?
Whoa!...Musta stood up too fast...
Ever stop to think and forget to start again?
An optomist is no more than a pessimist with an idea.
Gun control is hitting what you are aiming at.....
User avatar
Maz
Biker Mistress
Posts: 714
Joined: Tue Oct 25, 2011 4:02 pm
SELF INTRODUCTION: The Biker Mistress, Blonde, blue eyes, English Lady bike builder and previously a member of the CBH. I run my own custom bike and chop shop (MazChopz) on the south west coast of England. I have been building custom bikes for over 35 years and have built some 130 bikes so far. I am happy to share my knowledge and "expertise" and also hope to learn from the other forum members. I look forward to meeting up with many of my friends from the CBH and especially to seeing how Dan got on with his Knuck.
Location: South West Coast of England
Contact:

Re: Large Radius Tool

Post by Maz »

jimmib wrote:Nice Tool. What about chatter? Do you have any problems in that area?
Thanks Jimmib, we did get a bit of chatter when we first built it but then we added the lower support plate which has a clamp under the lathe bed...now we can work up to a radius the size of the faceplate without chatter :shifty: but it does get a bit scary at those sizes :hand:

Getting the tool shimmed into place also helped...if you get it mis-aligned or slightly loose then it will chatter.....a lot :doh:

Maz xx
Blonde, blue eyes, English Custom Bike builder and Biker Mistress!!!

Image
User avatar
jimmib
Lurker
Posts: 91
Joined: Tue Oct 25, 2011 1:35 pm
SELF INTRODUCTION: Hello everyone. first of all a big thanks to "Dan the Man". Some of you know me from the previous (2) boards and some don't, so here goes. I have been a fabricator/welder for over 40 years now. Damn that's a helluva long time to do anything! Anyways, I have built literaly 100's of street rods, pro streeters, racecars, bikes and trikes over the years. Never made the headlines and never will. I do what I do because it is the love of my life.
I enjoy reading the posts on the forum and try to contribute when I can. I am sure that this will be every bit as good as the CBH forum, as we will have most of the same folks. Good luck and post a lot of pics!! Jim
Location: Lowcountry USA

Re: Large Radius Tool

Post by jimmib »

Thanks Maz......I have used smaller radius cutters and was just wondering.
Jim
Whoa!...Musta stood up too fast...
Ever stop to think and forget to start again?
An optomist is no more than a pessimist with an idea.
Gun control is hitting what you are aiming at.....
rakeNtrail
Lurker
Posts: 50
Joined: Sat Oct 29, 2011 11:28 am
SELF INTRODUCTION: Just a grumpy old welder/chopperhedd Spent far too much time burning wire for a living but hey, one does have to pay the bills ya know! Worked shipyards and fab shops welding about everything stick, mig, tig and sub-arc. Both hand held and automated. Worked weekends in a Honda shop in the late 70's and in an all bike shop in the late 80's thru early 90's. Likes? Choppers, rock-N-roll, NRA and boobies! Dislikes? PC, VD, AARP & NAACP I'm pro business and totally against big government interfering in our daily lives. Live free or die baby and you'll have to pry it from my cold dead hands. Do love little children and puppies though. Both of them can turn me into a 300lb. old softie!
Location: North By God Carolina

Re: Large Radius Tool

Post by rakeNtrail »

Yep, everyone should have a large radius "tool" ! :laughing-rolling: :banana-dance: :dance: :banana-dance: :popcorn: :banana-dance: :whistle: :banana-dance: :doh:
User avatar
Maz
Biker Mistress
Posts: 714
Joined: Tue Oct 25, 2011 4:02 pm
SELF INTRODUCTION: The Biker Mistress, Blonde, blue eyes, English Lady bike builder and previously a member of the CBH. I run my own custom bike and chop shop (MazChopz) on the south west coast of England. I have been building custom bikes for over 35 years and have built some 130 bikes so far. I am happy to share my knowledge and "expertise" and also hope to learn from the other forum members. I look forward to meeting up with many of my friends from the CBH and especially to seeing how Dan got on with his Knuck.
Location: South West Coast of England
Contact:

Re: Large Radius Tool

Post by Maz »

rakeNtrail wrote:Yep, everyone should have a large radius "tool" ! :laughing-rolling: :banana-dance: :dance: :banana-dance: :popcorn: :banana-dance: :whistle: :banana-dance: :doh:
report to Mistress immediately :naughty:

:laughing-rolling:

Maz xx
Blonde, blue eyes, English Custom Bike builder and Biker Mistress!!!

Image
User avatar
Maz
Biker Mistress
Posts: 714
Joined: Tue Oct 25, 2011 4:02 pm
SELF INTRODUCTION: The Biker Mistress, Blonde, blue eyes, English Lady bike builder and previously a member of the CBH. I run my own custom bike and chop shop (MazChopz) on the south west coast of England. I have been building custom bikes for over 35 years and have built some 130 bikes so far. I am happy to share my knowledge and "expertise" and also hope to learn from the other forum members. I look forward to meeting up with many of my friends from the CBH and especially to seeing how Dan got on with his Knuck.
Location: South West Coast of England
Contact:

Re: Large Radius Tool

Post by Maz »

at the risk of more smutty comments :hand: here's an example of my large radius tool in use - these are one-off items I'm making for a customer from solid aluminium....
radtool002.jpg
radtool002.jpg (53.68 KiB) Viewed 28428 times
radtool003.jpg
radtool003.jpg (46.47 KiB) Viewed 28428 times
Maz xx
Blonde, blue eyes, English Custom Bike builder and Biker Mistress!!!

Image
User avatar
yona
Conventioneer
Posts: 278
Joined: Tue Oct 25, 2011 4:55 pm
SELF INTRODUCTION: Automotive weldor and fabricator for 45 years, like to dip in to both pools............make hand-tooled leather covered seats and bags.................jack of all trades........................63 years old......live in Baja Georgia, on the coast...former military
Location: Baja Georgia - St Johns River Inlet
Contact:

Re: Large Radius Tool

Post by yona »

Not sure ......but i don't think we are allowed to show our large radius tools on this forum..... : (
I.D.G.A.F.H.T.D.I.A.O.C.C.
User avatar
Maxthegardener
Builder
Posts: 384
Joined: Tue Oct 25, 2011 11:28 am
SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
Location: Angus, Scotland

Re: Large Radius Tool

Post by Maxthegardener »

Aint the size so they say.............how ya use it :D
Attachments
Photo0164.jpg
Photo0164.jpg (43.86 KiB) Viewed 28412 times
Post Reply

Return to “The Machine Shop”