Good oil pressure, and was an easy start.
https://vimeo.com/167203546
I have pulled it apart to get on with the rest of this build.
INSTALL A OPEN PRIMARY BELT DRIVE.....
-
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
-
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
Re: INSTALL A OPEN PRIMARY BELT DRIVE.....
The transmission came with a belt drive hub/sprocket.
Took it off yesterday, and am ordering a chain steup for this bike.
Had to remove the inner primary, but left all else in place.
I will use a 51 tooth rear sprocket I borrowed for mockup to set up the chain drive.
- Attachments
-
- TranyShaft.JPG (155.83 KiB) Viewed 9939 times
-
- Lurker
- Posts: 64
- Joined: Tue Oct 25, 2011 9:59 pm
- SELF INTRODUCTION: I first found the chopperbuilders handbook back in 2004. Thanks to the board, and all its members, I was able to build My bike, and have ridden it 25,000 miles. I learned a lot, made some friends, and had a great time building it
Re: INSTALL A OPEN PRIMARY BELT DRIVE.....
I used a chain on my build as well. definitely no room for a belt on mine either
I first found the chopperbuilders handbook back in 2004. Thanks to the board, and all its members, I was able to build My bike, and have ridden it 71,000 miles. I learned a lot, made some friends, and had a great time building it
-
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
Re: INSTALL A OPEN PRIMARY BELT DRIVE.....
Did you use HD parts ; what size is your rear tire?Jim Sawyer wrote:I used a chain on my build as well. definitely no room for a belt on mine either
-
- Lurker
- Posts: 64
- Joined: Tue Oct 25, 2011 9:59 pm
- SELF INTRODUCTION: I first found the chopperbuilders handbook back in 2004. Thanks to the board, and all its members, I was able to build My bike, and have ridden it 25,000 miles. I learned a lot, made some friends, and had a great time building it
Re: INSTALL A OPEN PRIMARY BELT DRIVE.....
I used a 1/2" offset front sprocket, and a stock HD flat rear sprocket . The offset sprocket is made by PBI
I first found the chopperbuilders handbook back in 2004. Thanks to the board, and all its members, I was able to build My bike, and have ridden it 71,000 miles. I learned a lot, made some friends, and had a great time building it
-
- Lurker
- Posts: 64
- Joined: Tue Oct 25, 2011 9:59 pm
- SELF INTRODUCTION: I first found the chopperbuilders handbook back in 2004. Thanks to the board, and all its members, I was able to build My bike, and have ridden it 25,000 miles. I learned a lot, made some friends, and had a great time building it
Re: INSTALL A OPEN PRIMARY BELT DRIVE.....
This chart shows some of their options
- Attachments
-
- offset sprocket.jpg (106.66 KiB) Viewed 9645 times
I first found the chopperbuilders handbook back in 2004. Thanks to the board, and all its members, I was able to build My bike, and have ridden it 71,000 miles. I learned a lot, made some friends, and had a great time building it
-
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
Re: INSTALL A OPEN PRIMARY BELT DRIVE.....
Thanks Jim, I got front and rear from PBI. Nice product.Jim Sawyer wrote: ↑Sun Sep 10, 2017 8:46 am I used a 1/2" offset front sprocket, and a stock HD flat rear sprocket . The offset sprocket is made by PBI