Ride the Loop
-
yona
- Conventioneer
- Posts: 278
- Joined: Tue Oct 25, 2011 4:55 pm
- SELF INTRODUCTION: Automotive weldor and fabricator for 45 years, like to dip in to both pools............make hand-tooled leather covered seats and bags.................jack of all trades........................63 years old......live in Baja Georgia, on the coast...former military
- Location: Baja Georgia - St Johns River Inlet
- Contact:
Re: Ride the Loop
Seamed materials come apart , especially if you put your ass on them ...LOL....and they tend to be pricey....Would have to have a sample to see if it can be laced, as I don't sew, glue, or pop-rivet anything together...
I.D.G.A.F.H.T.D.I.A.O.C.C.
-
hansgoudzwaard
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
Re: Ride the Loop
I needed a left side turn signal lense for the Buell. They are the same as BMW, Ducati, etc., I'm told. Went to the dealer ...$13. They would need to order one. Drove around the corner to a *used parts* shop, and got the whole thing for $5.
Lots of good new and used parts here, & complete bikes,etc.
So... if you are in the area, and need some parts, have a look here. You will probably save some bucks.
Lots of good new and used parts here, & complete bikes,etc.
- DSCN0697 (640x480).jpg (176.35 KiB) Viewed 1213 times
- DSCN0699 (640x480).jpg (175.93 KiB) Viewed 1213 times
-
Maxthegardener
- Builder
- Posts: 384
- Joined: Tue Oct 25, 2011 11:28 am
- SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
- Location: Angus, Scotland
Re: Ride the Loop
Hows the build doing Hans, and are you breaking the buell up to use it in your chop??
-
hansgoudzwaard
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
Re: Ride the Loop
Hi Max;
I will have been away from home for 9 months as of Mar. 25th, so nothing was done. I want to get on with it, but I won't be stripping the Buell. I'm going to leave it as is, and use a big twin 5 spd. setup. So once I get back, I can start bolting on some parts.
I will have been away from home for 9 months as of Mar. 25th, so nothing was done. I want to get on with it, but I won't be stripping the Buell. I'm going to leave it as is, and use a big twin 5 spd. setup. So once I get back, I can start bolting on some parts.
- UHWHAT?
- DSCN0703 (480x640) (375x500).jpg (188.08 KiB) Viewed 1206 times
-
Maxthegardener
- Builder
- Posts: 384
- Joined: Tue Oct 25, 2011 11:28 am
- SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
- Location: Angus, Scotland
Re: Ride the Loop
That shite isn't lost in translation.... 
-
yona
- Conventioneer
- Posts: 278
- Joined: Tue Oct 25, 2011 4:55 pm
- SELF INTRODUCTION: Automotive weldor and fabricator for 45 years, like to dip in to both pools............make hand-tooled leather covered seats and bags.................jack of all trades........................63 years old......live in Baja Georgia, on the coast...former military
- Location: Baja Georgia - St Johns River Inlet
- Contact:
-
hansgoudzwaard
- Contributor
- Posts: 804
- Joined: Wed Oct 26, 2011 10:43 pm
- SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name.
I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
Re: Ride the Loop
hahahaha..you guys are sick..lol.
"Pleasant Breezes" would not have been the same.
"Pleasant Breezes" would not have been the same.