SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere
Looking at the prices of 1 to 1 right angle drives available I had a thought (a rare and fleeting occurance these days)
How hard would it be to use the axle (half shafts) ends and the diff gears they spline into for making a custom RA drive ?
Harvest those parts from any fwd car trans and machine up a body to support them and you have a part you could not buy anywhere for the money you would have invested in it this DIY project !
SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name. I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
SELF INTRODUCTION: Jack of all. Master of none. Worked in a machine shop since I was 8. Desgined embedded computers for a few years. Done lots in between. If there's anything I've learned with certainty, "Anyone who looks like they know what they're doing is putting on an act."
SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere
SELF INTRODUCTION: Jack of all. Master of none. Worked in a machine shop since I was 8. Desgined embedded computers for a few years. Done lots in between. If there's anything I've learned with certainty, "Anyone who looks like they know what they're doing is putting on an act."
So, your wanting to convert shaft to chain??? That's even easier. Several yrs back I downloaded a "Spiral Bevel Gear" catalog from "Arrow Gear Company". It's loaded with tech details for the 90* drive. (It's too big to post here.)
SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere
Rudog I think you are in that group that thinks " It's better to spend money and save time and trouble" !
I am in the one that has LOTS of time but little money , this is a hobby not a business so if I can save money by expending X amount of time I'll grab my tools and get to work !
I am a life long scavenger and repurposer so it comes natural !
SELF INTRODUCTION: Jack of all. Master of none. Worked in a machine shop since I was 8. Desgined embedded computers for a few years. Done lots in between. If there's anything I've learned with certainty, "Anyone who looks like they know what they're doing is putting on an act."
SELF INTRODUCTION: Name is Max living in scotland ,and building my first bike, Which is derived from a buellM2 Cyclone..Started with an engine and a Drop seat frame wich was made to my spec by a more experienced builder. would like to learn more about the skills and techniques required to build a frame so I value being a member here...Cheers Max
SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name. I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere
No sketches , just an idea I had trying to figure a way to get a piece of equipment as cheaply as possible !
The bevel gears that each axle spline into seems to me to provide an excellent start for a right angle drive that should not beyond the skill levels of any practiced machinist !!
SELF INTRODUCTION: Jack of all. Master of none. Worked in a machine shop since I was 8. Desgined embedded computers for a few years. Done lots in between. If there's anything I've learned with certainty, "Anyone who looks like they know what they're doing is putting on an act."
SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere
SELF INTRODUCTION: Automotive weldor and fabricator for 45 years, like to dip in to both pools............make hand-tooled leather covered seats and bags.................jack of all trades........................63 years old......live in Baja Georgia, on the coast...former military
Look for a light (Aluminum) differential from anything that could handle the power and remove one axle ... that would give you a 90 degree ... a lot of small cars have aluminum IRS's.... Use a axle stub and make a mount for a chain gear.. like the Boss Hoss bikes....
SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere