If you got me if at all posible the actuall diemension from the part as the one diemensioned in the screen shot I could just connect the reccess in the print???
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
Thread looks good!
I will see if the dimension is online somewhere, otherwise I really do not want to take this apart again.
Somehow we will figure this out!
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
I have tried to find diemension for the carrier have you had any luck??
I really do not want to post/release the drawing and have several mad bikers looking for me because that diemension is off and they ruined $$$$$$ in aluminum billet!!!
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
Caliper cost 115.00 new with pads...the other I was going to use would of been 35.00 plus 27.00 for pads and been flat black. So I went with this one...other would just need a different mount made up.
Good eye on the step down...I didn't even catch it. Its merely cosmetic though, the important part is for the carrier to fit. I didn't even remember doing that but its only for the eye appeal.
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
Got the cut files for the steel bracket back from a fellow member here. Thanks Wendell
Hopefully they will be cut this week. Also got the caliper in and will be making up the mounting bracket this coming week.
SELF INTRODUCTION: I am an expat tennessee hillbilly and retired us navy engineer livin' in Scotland and I have a love of old cars , trucks, motorcycles and most any other machinery !
I dont know if I can think of enough to say to reach the two hundred charactor minimun set by the mods , but I will persevere
I remember as a small child riding with my father as he was driving an old mid '20s "T" home after buying it !
It had an external band brake on the axle pinion that worked just fine ... Until one rear wheel lost traction while braking hard on a wet red clay and gravel road and began spinning BACKWARDS at the same rpm as the other wheel was turning resulting in NO BRAKING AT ALL untill that wheel found traction again !
I heard a few new cuss words that day and I have to say my father was very profane as a rule ! It was a a long time before I even knew what those new words meant (other than a sore bottom if my mom or granma if heard me using them )
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
SELF INTRODUCTION: I was on the last board as bonustoolkit. I have changed that to my given name. I started a project build there " File and Fit." I paln to continue that when I go back home in Dec. 2011. I first joined the board when Gary W had it in the year 2005. That was the time I really gained an interest in building chops. I have a long way to go, compared to some here.
SELF INTRODUCTION: Former member of CBH....learning the ways to chop. Had a few bikes before....a few now...and lots more to come. Currently on a trike build, and a bike build. Thanks for having me back on board Dan. Hopefully I will do you guys proud!
Nope not a bolt on...this would require either modifications to an existing frame or in my case I will build a frame to work with this. That part will probably be a 2014 thing though