in the jig section i posted about building a motor mount fixture and template for an iron head. well attached are the finished photos of the frame
ironhead frame
-
- Conventioneer
- Posts: 277
- Joined: Sun Nov 06, 2011 12:46 pm
- SELF INTRODUCTION: Hey dan it chris (krymis) from the CBH board. thanks for opening this back up. hope to have a project to show the build here. BLAH BLAH BLAH BLAH BLAH and so on and so forth. The book of revolations and worlds ends and shit like that.....
- gww25
- Site Grandaddy
- Posts: 219
- Joined: Thu Nov 24, 2011 2:45 pm
- SELF INTRODUCTION: I'm just an old chopper builders who still dabbles in the craft and I hope that I can contribute something to the discussions as time goes by. Most of you already know that I started the Chopper Builders Handbook site so you're probably already familiar with my philosophy on choppers and chopper work.
- Location: Murphy, Texas
- Contact:
Re: ironhead frame
This turned out really nice, and I think, pretty darn original as well.
- budoka
- Site Admin
- Posts: 492
- Joined: Thu Jul 21, 2011 12:51 pm
- SELF INTRODUCTION: I'm a Kentucky boy who's found himself transplanted into Japan. been into turning wrenches as long as i can remember. i love muscle cars, hotrod bikes, and the martial arts.
been a member of this board since back when it was a part of Chopperweb. been handling the tech side and sharing the admin duties for several years now. - Location: Fuefuki Shi, Japan
- Contact:
Re: ironhead frame
now THAT is sweet!
-dan
-dan
-experience is a wonderful thing. It enables you to recognize a mistake when you make it again.
http://knuckleheadsummer.blogspot.com/
http://knuckleheadsummer.blogspot.com/
-
- NewB
- Posts: 15
- Joined: Sun May 12, 2013 4:40 pm
- SELF INTRODUCTION: I'm a retired Ironworker, I build custom chop seats, own a 71 Triumph, a 74 Ironhead, a 73 SOHC 750, & other junk. I want to learn machine work, & how to build frames, jigs, springer front ends as well as girders, & leafers.
Re: ironhead frame
Awesome.
- railroad bob
- Contributor
- Posts: 939
- Joined: Fri Nov 04, 2011 10:07 pm
- SELF INTRODUCTION: Hi Dan, thanks for your time and energy spent on this new board. I hope you will give me a waiver on the email account, I have used gmail so long I don't have a clue what my service provider account is.
I just returned home from a 2 week trip in New Mexico, have a few good pix, can't wait to share my off-highway traveling. Got to put 1400 miles on the scoot.
Best, Bob Davidson - Location: Alaska
Re: ironhead frame
That tubing arrangement on the rear section is unusual too me, looks really strong.
Alaska - Land of the Individual and Other Endangered Species
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL
-
- Conventioneer
- Posts: 277
- Joined: Sun Nov 06, 2011 12:46 pm
- SELF INTRODUCTION: Hey dan it chris (krymis) from the CBH board. thanks for opening this back up. hope to have a project to show the build here. BLAH BLAH BLAH BLAH BLAH and so on and so forth. The book of revolations and worlds ends and shit like that.....
Re: ironhead frame
bob that setup is actually the weak setup. he should have ran the from the seat post back to the axle plate then added in the vertical tube. he has the top of the axle block and tube now pushing a short length of tubing horizontally into the vertical tube. it will work but i would have rather he did it another way.
- railroad bob
- Contributor
- Posts: 939
- Joined: Fri Nov 04, 2011 10:07 pm
- SELF INTRODUCTION: Hi Dan, thanks for your time and energy spent on this new board. I hope you will give me a waiver on the email account, I have used gmail so long I don't have a clue what my service provider account is.
I just returned home from a 2 week trip in New Mexico, have a few good pix, can't wait to share my off-highway traveling. Got to put 1400 miles on the scoot.
Best, Bob Davidson - Location: Alaska
Re: ironhead frame
good point about the stresses from the axle plate going into the other tubing.
I took a second look, and you're right.
I took a second look, and you're right.
Alaska - Land of the Individual and Other Endangered Species
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL
An Armed Society is a Polite Society,...
Politicians Prefer Unarmed Peasants
TANSTAAFL